Jet Cat engine
 
 
Jet Cat P60-SE Special Edition Price: $2,495.00
 

JetCat P60-SE SPecial Edition Turbine complete with starter includes:
 

  • Jet-tronic ECU (fuel control electronics)

  • GSU (Display and Programmer)

  • LED I/O board

  • Miniature fuel pump

  • Electronic starting gas valve

  • Electronic Fuel valve

  • Fuel tubing, tubing connector set, filters, and cable set

  • 2 cell, 2500mA LiPoly battery pack

  • Starting gas tank

  • Turbine mounting clamp, RamTec compatible

  • Detailed instruction manual

Thrust: 13 LB @ 165,000 RPM
 
Weight: 1.87 LB, incl. starter
 
Diameter: 3.25 inches
 
RPM Range: 50,000 - 165,000
 
Exhaust gas temp.: 580°C -690°C
 
Fuel consumption: 8 oz per/min at full power
 
Fuel: Jet A1, 1-K kerosene
 
Lubrication: approximately 5% synthetic turbine oil in the fuel
 
Maintenance interval: 25 hours
 

 
JetCat P70 turbine Price: $2,650.00

JetCat P-70 turbine complete with starter includes:
 

  • Jet-tronic ECU (fuel control electronics)

  • GSU (Display and Programmer)

  • LED I/O board

  • Miniature fuel pump

  • Electronic starting gas valve

  • Electronic Fuel valve

  • Fuel tubing, tubing connector set, filters, and cable set

  • 2 cell, 2500mA LiPoly battery pack

  • Starting gas tank

  • Turbine mounting clamp, RamTec compatible

  • Detailed instruction manual
     

    Thrust: 17.5 LB @ 123,000 RPM
     
    Weight: 2.6 LB, incl. starter
     
    Diameter: 3.7 inches
     
    RPM Range: 35,000 - 123,000
     
    Exhaust gas temp.: 620°C
     
    Fuel consumption: 8 oz per/min at full power
     
    Fuel: Jet A1, 1-K kerosene
     
    Lubrication: approximately 5% synthetic turbine oil in the fuel
     
    Maintenance interval: 25 hours
     
    P70 Thrust Chart
     
    RPM Thrust
    38,000 0.75
    93,000 8.0
    101,000 10.0
    107,000 12.0
    113,000 14.0
    118,000 16.0
    123,000 17.5

    The values are approximate and can vary slightly from engine to engine.
    Values at Standard Temperature and Pressure.

 
JetCat P80-SE turbine Price: $2,395.00
 

Introducing the new JetCat P80-SE with more POWER and enhanced reliability.

The P80-SE continues our extreemly successfull P80 engine. The new design of the P80-SE incorporates an optimized compressor/diffusor-system, resulting in higher engine performance and reliability.

The engine follows throttle commands almost without delay. In addition to the outstanding features of or ECU V6.0, the new ECU V6.3 has an „auto power down“ function built in, which allows to switch off the engine power supply (--> receiver off) before the engine cool down sequence has been finished. In this case the ECU will stay powered on, finish the cool down sequence and then auto power down itself.

JetCat P-80-SE turbine complete with starter includes:
 
  • Jet-tronic ECU (fuel control electronics)
  • GSU (Display and Programmer)
  • LED I/O board
  • Miniature fuel pump
  • Electronic starting gas valve
  • Electronic Fuel valve
  • Fuel tubing, tubing connector set, filters, and cable set
  • 2 cell, 2500mA LiPoly battery pack
  • Starting gas tank
  • Turbine mounting clamp, RamTec compatible
  • Detailed instruction manual
     
    Thrust: 22 LB @ 125,000 RPM
     
    Weight: 2.9 LB, incl. starter
     
    Diameter: 4.4 inches
     
    RPM Range: 35,000 - 125,000
     
    Exhaust gas temp.: 580°C -690°C
     
    Fuel consumption: 9 oz per/min at full power
     
    Fuel: Jet A1, 1-K kerosene
     
    Lubrication: approximately 5% synthetic turbine oil in the fuel
     
    Maintenance interval: 25 hours
     
    P80-SE Thrust Chart
     
    RPM Thrust
    35,000 0.8
    85,000 8.0
    93,000 10.0
    101,000 12.5
    110,000 15.0
    117,000 17.0
    118,000 18.0
    120,000 20.0

    125,000

    22.00

    The values are approximate and can vary slightly from engine to engine.
    Values at Standard Temperature and Pressure.
     
     

     

 
JetCat P120-SX turbine Price: $3,495.00
 

JetCat P-120-SX turbine complete with starter includes:
 

  • Jet-tronic ECU (fuel control electronics)

  • CAD designed and machined from billet compressor wheel

  • Internal kerosene starting plug for single fuel operation. Fast startup!

  • GSU (Display and Programmer)

  • LED I/O board

  • Miniature fuel pump

  • Electronic starting gas valve

  • Electronic Fuel valve

  • Fuel tubing, tubing connector set, filters, and cable set

  • 2 cell, 2500mA LiPoly battery pack

  • Turbine mounting clamp, RamTec compatible

  • Detailed instruction manual

    Thrust: Thrust is 30 lbs @ 125,000 RPM
    Weight: 3.1 LB
     
    Diameter: 4.4 inches
     
    RPM Range: 33,000 - 125,000 RPM
    Exhaust gas temp.: 580°C-690°C
     
    Fuel consumption: 12oz/min at full power
     
    Fuel: Jet A1, 1-K kerosene
     
    Lubrication: approximately 5% synthetic turbine oil in the fuel
     
    Maintenance interval: 25 hours
     

    P120-SX Thrust Chart
     

    V4.0-5.0 ECU with a maximum of 125K RPM allowable in the limits menu. Thrust
    33,000 1.0
    82,000 9.5
    90,000 12.0
    92,500 13.0
    98,500 15.0
    103,500 17.0
    105,500 18.0
    111,000 20.0
    115,000 22.0
    119,000 24.0
    121,000 26.0
    123,000 28.0
    125,000 30.0

    The values are approximate and can vary slightly from engine to engine.
    Values at Standard Temperature and Pressure.

 

JetCat P160-SX turbine Price: $4,195.00

JetCat P160-SX turbine complete with starter includes:
 

  • 6 lbs more thrust than the P120-SX

  • CAD designed and machined from billet compressor wheel

  • Internal kerosene starting plug for single fuel operation. Fast startup!

  • Jet-tronic ECU (fuel control electronics)

  • GSU (Display and Programmer)

  • LED I/O board

  • Miniature fuel pump

  • Electronic starting gas valve

  • Electronic Fuel valve

  • Fuel tubing, tubing connector set, filters, and cable set

  • 2 cell, 2500mA LiPoly battery pack

  • Turbine mounting clamp, RamTec compatible

  • Detailed instruction manual
     

    Thrust: 36 lbs @ 125,000 RPM
     
    Weight: 3.1 LB
     
    Diameter: 4.4 inches
     
    RPM Range: 32,000 - 125,000 RPM
    Exhaust gas temp.: 650°C-750°C
     
    Fuel consumption: 17 oz per/min at full power
     
    Fuel: Jet A1, 1-K kerosene
     
    Lubrication: approximately 5% synthetic turbine oil in the fuel
     
    Maintenance interval: 25 hours
     

    P160-SX Thrust Chart

    RPM Thrust
    32,000 1.0
    100,000 19.0
    105,000 22.0
    115,000 28.5
    120,000 31.8
    123,000 34.0
    125,000 36.0

    The values are approximate and can vary slightly from engine to engine.
    Values at Standard Temperature and Pressure

 
JetCat P180 turbine Price: $4,995.00

JetCat P-180 turbine comes complete with HEAVY DUTY starter and includes:

  • Jet-tronic ECU (fuel control electronics)

  • GSU (Display and Programmer)

  • LED I/O board

  • Miniature fuel pump

  • Electronic starting gas valve

  • Electronic Fuel valve

  • Fuel tubing, tubing connector set, filters, and cable set

  • 2 cell, 3800mA LiPoly battery pack

  • Starting gas tank

  • Turbine mounting clamp, RamTec compatible

  • Detailed instruction manual
     

    Thrust: 45 lbs @ 110,000 RPM
     
    Weight: 5 LB
     
    Diameter: 4.72 inches
     
    RPM Range: 32,000 - 110,000 RPM
    Exhaust gas temp.: 580°C-720°C
     
    Fuel consumption: 24 oz per/min at full power
     
    Fuel: Jet A1, 1-K kerosene
     
    Lubrication: approximately 5% synthetic turbine oil in the fuel
     
    Maintenance interval: 25 hours
     

    The values are approximate and can vary slightly from engine to engine.
    Values at Standard Temperature and Pressure.

 
JetCat P200 turbine Price: $5,495.00
 
JetCat P-200 turbine comes complete with HEAVY DUTY starter and includes:
  • Jet-tronic ECU (fuel control electronics)
  • GSU (Display and Programmer)
  • LED I/O board · Miniature fuel pump
  • Electronic starting gas valve
  • Electronic Fuel valve
  • Fuel tubing, tubing connector set, filters, and cable set
  • 2 cell, 3800mA LiPoly battery pack
  • Starting gas tank
  • Turbine mounting clamp
  • Detailed instruction manual
    Thrust: 52 lbs @ 112,000 RPM
     
    Weight: 5 LB
     
    Diameter: 5.12 inches
     
    RPM Range: 32,000 - 110,000 RPM
    Exhaust gas temp.: 580°C-720°C
     
    Fuel consumption: 24 oz per/min at full power
     
    Fuel: Jet A1, 1-K kerosene
     
    Lubrication: approximately 5% synthetic turbine oil in the fuel
     
    Maintenance interval: 25 hours